

_1346074401.jpg)
Q-FLOOR
Ứng dụng chính:Q-FLOOR giúp vệ sinh sàn nhà, văn phòng, siêu thị, trường học, bệnh viện và tiền sảnh các khu công cộng. Hiệu quả cao trên bề mặt sàn đá cẩm thạch, hoa cương, gạch men và gỗ. DÙNG CHO CÔNG NGHIỆP VÀ GIA DỤNG.
Hướng dẫn sử dụng:
Pha loãng với nước tỷ lệ 1:40-1:20. Dùng cây lau hoặc khăn lau sạch. Nếu dùng với tỷ lệ 1:80 (tương đương 1 nắp 50ml với 1 chậu 4 lít nước sạch) thì không cần lau lại với nước. Lưu ý: Tránh tiếp xúc với mắt. Đậy nắp kỹ sau khi sử dụng. Để xa tầm tay trẻ em.
Bảo quản:
Bảo quản nơi khô ráo thoáng mát, tránh ánh nắng trực tiếp.
XEM THÊM TÀI LIÊU AN TOÀN (MSDS) ĐỂ BIẾT THÊM THÔNG TIN
_1346074401.jpg)
_1346074962.jpg)
Q-VANI
Ứng dụng chính:Vệ sinh và đánh bóng nội thất, đồ đạc gia đình, nội thất ô tô và nhiều bề mặt gỗ. DÙNG CHO CÔNG NGHIỆP VÀ GIA DỤNG.
Hướng dẫn sử dụng:
Phun trực tiếp lên bề mặt gỗ. Lau sạch vết bẩn bằng giẻ lau chuyên dụng và để khô tự nhiên.
Lưu ý:
Tránh tiếp xúc với mắt. Đậy nắp kỹ sau khi sử dụng. Để xa tầm tay trẻ em.
Bảo quản:
Bảo quản nơi khô ráo, thoáng mát, tránh ánh nắng trực tiếp.
XEM THÊM TÀI LIÊU AN TOÀN (MSDS) ĐỂ BIẾT THÊM THÔNG TIN
_1346074962.jpg)
_1346075402.jpg)
Q-GLAZE
Ứng dụng chính:Q-GLAZE vệ sinh các bề mặt kính trong nhà và ngoài trời. Vệ sinh làm bóng kính cửa sổ, cửa ra vào, kính ô tô, các bề mặt mi ca, sành, sứ và nhựa. DÙNG CHO CÔNG NGHIỆP VÀ GIA DỤNG.
Hướng dẫn sử dụng:
Sử dụng nguyên chất hay pha loãng tỉ lệ 1:30 – 1:10 với nước. Phun trực tiếp lên bề mặt kính cần vệ sinh, dùng giẻ lau hoặc cây gạt lau sạch
Lưu ý:
Tránh tiếp xúc với mắt. Đậy nắp kỹ sau khi sử dụng. Để xa tầm tay trẻ em.
Bảo quản:
Bảo quản nơi khô ráo thoáng mát. Tránh ánh nắng trực tiếp.
XEM THÊM TÀI LIÊU AN TOÀN (MSDS) ĐỂ BIẾT THÊM THÔNG TIN
_1346075402.jpg)
_1346075800.jpg)
Q-CARPET
Ứng dụng chính:Sử dụng cho máy giặt thảm dạng phun hút. DÙNG CHO CÔNG NGHIỆP VÀ GIA DỤNG.
Hướng dẫn sử dụng:
Pha Q-CARPET trong nước tỉ lệ 1:30 – 1:10 tùy thuộc độ dơ của thảm. Cho dung dịch đã pha vào máy giặt thảm và tiến hành giặt bình thường.
Lưu ý:
Tránh tiếp xúc với da, mắt, quần áo. Đậy nắp kỹ sau khi sử dụng. Để xa tầm tay trẻ em.
Bảo quản:
Bảo quản nơi khô ráo thoáng mát, tránh ánh nắng trực tiếp.
XEM THÊM TÀI LIÊU AN TOÀN (MSDS) ĐỂ BIẾT THÊM THÔNG TIN
_1346075800.jpg)
_1346076223.jpg)
Q-EFFECT
Ứng dụng chính:Q–EFFECT thích hợp cho việc vệ sinh sàn đá hoa cương, cẩmthạch của hộ gia đình, văn phòng, khách sạn, nhà hàng và tiền sảnh các khu côngcộng. Cũng dùng trên các bề mặt kim loại, men sứ, kính và gỗ. DÙNG CHO CÔNGNGHIỆP VÀ GIA DỤNG.
Hướng dẫn sử dụng:
Pha loãng với nước tỷ lệ 1:30-1:10 tùy thuộc độ dơ trên sàn. Dùng cây lau hoặc khăn lau sạch.
Lưu ý:
Tránh tiếp xúc với mắt, quần áo. Đậy nắp kỹ sau khi sử dụng. Để xa tầmtay trẻ em.
Bảo quản:
Bảo quản nơi khô ráo thoáng mát, tránh ánh nắng trực tiếp.
XEM THÊM TÀI LIÊU AN TOÀN (MSDS) ĐỂ BIẾT THÊM THÔNG TIN
_1346076223.jpg)
_1346076740.jpg)
Q - NOX
Ứng dụng chính:Đánh bóng làm mới bếp, ống khói, hộc, bồn rửa, lò, giá kệ, và các thiết bị bếp khác. Vệ sinh bồn rửa, bề mặt thiết bị inox trong công nghiệp chế biến thực phẩm. Đánh bóng thang máy, cửa, tay vịn cầu thang và nhiều vật dụng làm bằng inox khác. Làm mới và bảo trì các bề mặt nhôm tĩnh điện. DÙNG CHO CÔNG NGHIỆP VÀ GIA DỤNG.
Hướng dẫn sử dụng:
Làm khô bề mặt cần vệ sinh. Dùng trực tiếp Q-Nox bằng cách làm ẩm khăn lau với Q-NOX rồi lau lên bề mặt. Hoặc phun xịt một lớp mỏng Q-Nox. Sauđó lau bóng với khăn sạch.
Lưu ý:
Tránh tiếp xúc với mắt và da. Không đâm thủng hoặc đốt bình đựng hóa chất. Đậy nắp bình sau khi sử dụng. Để xa tầm với trẻ em.
Bảo quản:
Bảo quản nơi khô ráo. Không để gần nguồn lửa.
XEM THÊM TÀI LIÊU AN TOÀN (MSDS) ĐỂ BIẾT THÊM THÔNG TIN
_1346076740.jpg)
Tạo lớp phủ bóng cho sàn I Thích hợp cho mọi chất liệu sàn I Lớp phủ có độ bền cao, chịu được nước, hóa chất và cọ xước I Dễdàng vệ sinh trên bề mặt phủ bóng và bảo trì

Q-GLOSS là chất đặc chủng được nghiên cứu để tạo cho các chất liệu mặt sàn lớp phủ bóng bền, sáng bóng với giá thành hợp lý. Lớp phủ của Q-GLOSS màu trong, bóng và có độ bền cao, chịu được nước, hóa chất và cọ xước.
Đặc biệt phù hợp cho việc bảo trì như vệ sinh trên bề mặt lớp phủ và thay lớp phủ mới.
Q-GLOSS
Ứng dụng chính:
Q-GLOSS dùng trên mọi chất liệu sàn đàn hồi và cứng, bao gồm nhựa, nhựa vinyl amiăng, đá hoa cương, cẩm thạch, sàn gỗ và xi măng.
Dùng cho công nghiệp và gia dụng.
Hướng dẫn sử dụng:Thao tác tiến hành như sau:
- Làm sạch bề mặt sàn
- Ngay khi bề mặt sàn khô, phủ từ 1-2 lớp Q-GLOSS bằng dụng cụ chuyên dụng cho thật đều và chờ cho khô bề mặt. Lưu ý mỗi lớp phủ phải thật mỏng và phủ lớp tiếp theo khi lớp trước hoàn toàn khô. Tránh thi công khi có gió to tạo gợn trên bề mặt lớp phủ.
Thời gian sử dụng thường là 4-12 tuần trên bề mặt sàn nhựa và 3-5 tuần trên bề mặt sàn đá tùy theo mật độ đi lại trên bề mặt sàn. Sau thời gian này tiến hành bảo dưỡng tiếp.
Lưu ý:
Tránh tiếp xúc với mắt. Để xa tầm với trẻ em.
Bảo quản:
Bảo quản nơi khô thoáng.
XEM THÊM TÀI LIỆU AN TOÀN KỸ THUẬT (MSDS) ĐỂ BIẾT THÊM THÔNG TIN.
_1416363776.jpg)
Q-CAR CLEAN
Main applications: For cleaning of cars and all types of transport vehicles.
Directions for use: Dilution rate is 1:100, apply on surface for few min. Then rinse with high pressure water
Q-SAFESANI
Main applications: To clean, deodorize and disinfect toilet bowls, urinals and bathroom sinks, ceramic wall and floor tiles.
Directions for use: Squirt a light stream over the inside of the bowl or urinal. Note how it clings to the surfaces. Spread around the bowl and under the rim with a bowl mop. Use same process for sinks, bathtubs, ceramic floors and wall tiles. Allow to act for at least a few minutes. Flush clean. Rinse mop.
Q-CREAM CLEAN
Main applications: To remove tarnish from brass, bronze and cooper easily and quickly without leaving a dull finish or imparting an offensive odour.
Directions for use:
Hockey arenas: apply with a sponge, paint roller or brush. Brush the puck marks on the safety glass until they disappear. Rinse with water.
Kitchen and bathrooms: apply with a sponge, using light pressure, to clean fibreglass, plastic, porcelain, formica, chrome, tiles, stainless steel, appliance enamel, ect.
Tarnish removal on metal: apply to s sponge and clean surface by rubbing the tarnished area until the tarnish is removed. Wipe clean with a moistened clean cloth or sponge.
Brass surfaces: after tarnish has been removed and wiped off, apply STAINLESS STEEL POLISH directly to surface and polish with a clean cloth. The surface may be cleaned whenever required with STAINLESS STEEL POLISH and the tarnish removed only when required, perhaps on a monthly basis.
Q-RUST REMOVE
Main applications: To remove rust spots on carpet, stone floors and sanitary installations.
Directions for use: Dissolve 1 part of Q-RUST REMOVE in 2 parts of water. Apply sparingly and observe the spot and do not leave it unattended. Remove the surplus with a sponge and water. Repeat. Apply the undiluted cleaner and the same way for and rinse with water. On carpets remove the water with a dry cloth as good as possible. Avoid too much friction and prevent walking on the area until dry.
Q-MOKET
Main applications: To remove spots from rugs and carpet
Directions for use: Shake the container well and foam the product on the area to be treated. Rub gently with a clean cloth or sponge.Do not apply too strong mechanical action in order to avoid damage to the dye. Especially dark shades are sensitive to friction. Wash out with water, remove surplus with a dry towel or cloth. Do not walk on area for 24 hours. Remove remaining dust and detergent with a vacuum cleaner.
Q-CRYSTAL
Main applications: To give marble and terrazzo floors a durable, high, uniform gloss.
Directions for use: Use after the floor has been prepared with Q-FLOOR COND. Use with a rotary buffing machine at 250-600 rpm and 15-30 ml of Q-CRYSTAL per square metre. A heavy machine (40-70kg) gives better results than a lighter one. Use a fine steel wool pad with the floor machine. After the Q-CRYSTAL solution has been buffed into the floor, the floor can then be dry-buffed with a synthetic grade pad to produce a high gloss. Maintenance of the treated floors and surfaces is achieved by periodic, i.e. weekly, biweekly, monthly, ect., application by buffing of Q-CRYSTAL to the treated floor.
Q-FLOOR COND
Main applications: To prepare marble and terrazzo floors for crystallising with Q-CRYSTAL
Directions for use: Shake well. Use with a rotary buffing machine and a black pad at 250-600 rpm and 15-30 ml of Q-FLOOR COND per square metre. A heavy machine (40-70kg) gives better results than a lighter machine. Buff the floor until dry (usually in a few minutes). Apply Q-CRYSTAL according to direction for this product. For vertical border surfaces and surfaces too small to receive a buffing machine, Q-FLOOR COND can be applied by hand with either a synthetic pad or a hand sanding (orbital) machine.
Q-REFINISH
Main applications: To clean floors and strip floor finishes from TERRAZZO, MABLE, TRAVERTINE, CERAMIC TILE, and SLATE
Directions for use: To remove detergent resistant hard finishes and water based sealers, dilute as follows:
- light build up: 1 part Q-REFINISH per 10 parts of warm water.
- heavy build up and sealers: 4 part Q-REFINISH per 10 parts of warm water
Prepare solution according to above dilution recommendation. Apply solution with a mop. Allow to soak for 3 to 5 minutes in order to soften the build up. Scrub with floor machine using a nylon or polyester stripping pad. Pickup solution with mop or wet pick up vacuum machine. Rinse thoroughly with clear water. Allow to dry before applying new finish.
Apply finish or seal floor before opening to traffic.
Q-FORTEX
Main application: To clean tile, stone and plastic floors
Directions for use: Q-FORTEX can be used in a 1-2% diluted form. Stubborn marks and can be treated with a 1:1 dilution.